• High Pressure Oil Seal CFW
  • High Pressure Oil Seal CFW
  • High Pressure Oil Seal CFW
  • High Pressure Oil Seal CFW
  • High Pressure Oil Seal CFW
  • High Pressure Oil Seal CFW
  • High Pressure Oil Seal CFW
  • High Pressure Oil Seal CFW

High Pressure Oil Seal CFW

High-pressure shaft oil seal in sizes from 18×30×6 to 165×190×13. Send your old seal number or shaft and bore measurements to confirm.
$0.00 $1.91
    Please select the information you wantX
  • CFW骨架
Quantity
-
+
  • Description
Close-up of Simmerring packaging label with 70x90x7 specifications.Dark blue rotary shaft oil seals arranged on a plain surface.Three dark blue rotary shaft seals with visible metal garter springs.Dark blue rotary shaft seal inside a clear printed plastic bag.Dark blue Simmerring seal in clear branded bag with specification label.Close-up of Simmerring packaging labels with compound and cure-date details.

Product Overview

This high-pressure shaft oil seal is a rotary shaft seal: a circular ring with a rubber-covered case that presses into a housing bore and runs against a rotating shaft. It keeps oil inside a gearbox, pump, motor or engine housing and keeps dust, water and grit out. The lip is spring-loaded, so it stays in contact with the shaft as the rubber beds in and wears.

It is not a cylinder rod seal, a piston seal or a floating seal. Cylinder rebuilds use rod seals, main seals, piston seals, buffer rings and back-up rings; this radial oil seal sits where a shaft leaves a housing — a travel motor output, a pump drive, a gearbox input or a crank end. If you are resealing a cylinder, this is the wrong part.

Sizes follow the usual three-figure order: shaft diameter, housing bore and seal width, which is also how a wholesale oil seal order is quoted. Read the marking on the old seal the same way and you have the size you need without measuring anything.

Each size is a loose seal in its own right — you order the size, not a kit. That suits workshops keeping common sizes on the shelf and distributors who want one oil seal supplier for a mixed list.

Seal Construction

  • Rubber-covered outer case. The moulded jacket grips the housing bore and seals the static joint, and it tolerates minor bore imperfections better than a bare metal case. The body is dark blue, which is a moulding identification rather than a performance rating, so match the part by its three dimensions.
  • Spring-loaded lip. A garter spring behind the inner lip keeps radial load on the shaft as the rubber ages. Handle a rubber oil seal by the outer case, never by the lip — gripping the lip can dislodge the spring.
  • High-pressure lip profile. The lip and case are built for the higher pressure at a pump or motor shaft exit, where a plain lip seal would be pushed away from the shaft. Tell us the pressure on the oil side and how the housing is arranged, and we will confirm the choice.
  • Compact section. One design covers shallow pump covers and deeper hub bores, so a wholesale oil seal range needs fewer part numbers, and the narrow versions matter where there is very little room behind the lip.
  • Markings on the face. Size, compound code and cure date are moulded or printed on the outer face or on the bag. Read them before the old seal is binned: they are the quickest route to the right replacement (an oil seal supplier can match a size from the marking alone), and two entries in this list carry a TC prefix before the three figures.
  • Compound check. The code on the seal tells you what the original was. If the application runs hot oil, as a gearbox oil seal often does, or a fluid that attacks standard nitrile, send the oil type and working temperature and we will check the compound before shipping.

Specifications

PropertyValue
Seal typeHigh-pressure rotary shaft oil seal
DesignationCFW
Seal formRadial oil seal with a rubber-covered case and spring-loaded inner lip
Shaft diameter range18 to 165
Housing bore range30 to 190
Width range5.5 to 13
CaseRubber-covered, press fit
Supplied asLoose seal, ordered by size

Size Range

Size groupSizes listed (all dimensions in mm)
18–22 shaft18×35×8, 18×30×6, 22×42×10
25 shaft25×35×6, 25×40×6, 25×42×10, 25×47×6, 25×37×6/5.5, 25×40×10
28–32 shaft28×40×6, 28×40×5.5, 30×42×6, 30×50×7, 30×40×7, 32×42×6
35 shaft35×56×6, 35×54×6, 35×52×6
40–42 shaft40×62×6, 40×67×7, 40×55×6, 42×62×7
45 shaft45×65×8, 45×70×7, 45×65×7, 45×62×7, 45×80×7
50–52 shaft50×80×7, 50×80×8, 50×70×10, 50×72×7, 52×72×7
55 shaft55×70×6, 55×70×7/8, 55×75×7, 55×78×8
60–75 shaft60×80×7, 62×85×6.5, 65×90×7, 70×90×7, 75×95×10
TC-marked sizesTC-80×100×10, TC-95×115×8
Large bore140×160×8, 165×190×13

Size Callout & Fitment Check

  1. Read the three figures in shaft × bore × width order. On a 45×65×8 seal the shaft is 45, the bore 65 and the body 8 wide; put them in any other order and the seal will not fit.
  2. Look at the old seal first. Measure the shaft where the lip actually runs, not on an unworn section, and take readings at two points 90° apart.
  3. Measure the housing bore across two directions and note how deep the old seal sat. An out-of-round bore will leak even with the correct size; on an engine oil seal tucked into a thin cover, the old seating depth is worth noting too.
  4. Send the machine model, the numbers and a photo of the old part. As an oil seal supplier we match on dimensions and markings rather than model names alone, since one model can carry different housings across production years. Building a stock list? Start from the sizes your own machines and regular customers use, then widen it. If nothing in the list matches, send the measurements anyway and we will say whether another profile in the range is a closer fit.

Applications

  • Travel and swing motor output shafts. The shaft leaves the motor housing straight into dust and mud, so the seal holds oil in and grit out; a gearbox oil seal that starts to weep shows as oil on the motor casing or the track frame.
  • Hydraulic and gear pump drive shafts. The drive end sees the pressure this design is intended for, and a worn lip usually shows as oil misting around the pump flange.
  • Gearbox and transmission input or output shafts. Replacement is routine during a rebuild, and the number on the old seal usually settles the choice faster than a model lookup.
  • Crank ends on truck and machine engines. Front or rear engine oil seal positions use this shape of seal; when one starts to seep, the first sign is usually oil at the bell housing or behind the crank pulley.
  • Wheel hubs, final drives and axle ends. These run in dust and water, and a radial oil seal caught early is the cheapest part of an expensive repair.
  • Workshop stock and repair counters. Mixed fleets mean mixed sizes, and the sizes that move fastest are worth keeping within reach.
  • Trucks and general construction machinery. The same seal pattern turns up across excavators, trucks and other construction equipment, so measure before you assume a size.

Installation Notes

  1. Clean the bore and the shaft before anything else — solvent on a lint-free cloth, then dry. On an engine oil seal that has been leaking, degrease the housing properly so the new case grips instead of creeping out.
  2. Check the shaft for a wear ridge, scoring or corrosion at the lip line, and the bore for burrs at the entry chamfer. A small burr can shave rubber off the case as the seal goes in.
  3. Oil the lip and the bore lightly with the system oil. Never fit the seal dry, and keep grease away from the lip.
  4. Press the rubber oil seal in squarely with a driver or a flat plate that bears on the outer case. Hammering on the face distorts the case, and a blow on the lip damages the spring.
  5. Seat it to the depth the old seal sat at, or flush with the housing face on a plain through-bore. On a crankshaft oil seal, going deeper than the original position can cover an oil return path or push the lip out of its running position.
  6. Turn the shaft by hand afterwards to check the lip has not rolled and the seal sits square in the bore. Top up the oil, run up to working temperature and check the joint again after the first shift.

Ordering & Delivery

Order by the three dimensions or by the number moulded on the old seal — either works for a gearbox oil seal or a pump drive, and we confirm the match before dispatch. Send both if you have them; it removes the guesswork.

One seal for a repair or a wholesale oil seal order across several sizes goes through the same process; the only difference is how the lines are grouped. Seals are supplied individually bagged and labelled, which keeps sizes apart in a mixed box.

Stock and dispatch time depend on the size, so confirm both with your sales contact before you rely on a date — common sizes move faster than large or slow-moving ones. Ask about sample availability if you want to see the compound and finish before committing to a quantity.

Shipping terms, payment method and export packing are agreed with your sales contact when you order. Tell us the destination and whether the seals travel with heavier parts, so they are packed where they will not be crushed.

Scale & Supply Capability

Guangzhou Wason Construction Machinery has been supplying construction machinery parts since 2015, working with buyers across Africa, the Middle East, South America and other markets. As a trading company we buy through a broad supplier network, so we can cover a wide range of parts, keep fast-moving items in stock for quick dispatch, and combine different references into one consolidated order. Send us a part number, a photo or a cross-reference and we will confirm availability, check the specification with you, and coordinate customised or repeat requirements before shipment.

FAQ

Where exactly does this seal sit?

It presses into a housing bore and its lip runs on a rotating shaft — a pump drive, a motor output, a gearbox shaft or a crank end. It is not a cylinder rod seal or a floating seal, so it will not replace those parts in a cylinder rebuild.

The shaft has a wear groove where the old lip ran. Can I still fit this seal?

Often yes, with care. A light polish may be enough; a deeper ridge usually means the new lip has to sit at a slightly different depth, or the shaft needs a sleeve. Send close-up photos of the shaft and the bore and we will tell you what is realistic before you commit.

What rubber is the seal made from?

The body is a rubber oil seal with a moulded case and a spring-loaded lip, and the compound code is marked on the face or on the bag. If your oil or working temperature is unusual, send the details and we will check the compound against them before shipping.

What are the two TC-marked sizes?

The TC prefix is part of the number, not a separate product family. Two sizes in this range are written with it — TC-80×100×10 and TC-95×115×8 — while every other entry uses the plain three-figure callout. Keep the prefix attached when you quote the size, so whoever prices or picks the order knows exactly which entry you mean.

Treat the prefix as a way of identifying the size rather than as a pressure class, a compound grade or a sign that the seal is built differently from the rest of the list. If a customer's paperwork shows the same three figures without the prefix, or with a different maker's letters in front of them, send a photo of the marking together with your measurements and we will confirm which entry matches instead of guessing from the numbers alone.

For shelf stock, write the full callout on the bin label, prefix included. A ticket that drops the prefix reads like any other size to a picker working quickly through a rack of loose seals, and the mistake only shows up at the press. Distributors cross-referencing an aftermarket part number should send that number alongside the dimensions, because a match on the figures by itself is thin evidence when a prefix is involved.

If the old part carries no legible marking, measure the shaft, the housing bore and the seal width and send those instead of a part number. We will tell you whether the TC-marked entry is the one to order or whether your measurements point somewhere else in the list.

Will it work at a crankshaft end on a truck engine?

A crankshaft oil seal position is the right kind of duty for this seal, but fit depends on the shaft and bore dimensions rather than the model. Confirm the size against the old part and check the shaft surface at the lip line before fitting.

My size is not in the list. What now?

Measure the shaft first, across a section the lip has not polished, because a deep wear groove makes a good shaft read undersize. Take the housing bore with the old seal out and the bore wiped clean, and measure the width across the case rather than across the lip. Give all three figures in millimetres, or say plainly that your instruments are imperial, and add the machine model and where the seal sits — travel motor output, pump drive, gearbox input or crank end — since the same shaft size can turn up in more than one housing on one machine.

Photos save a round of questions: the old seal face up next to a rule, the marking if any survives, and the housing with the bore in view. Mention a dust lip, a garter spring or an unusually shallow case if you see one, because profile detail decides the choice as much as the three figures do. Tell us the pressure on the oil side and how the housing is arranged as well, so the suggestion suits a pressurised shaft exit and not a plain cover.

If nothing in the range is close, we will say so. Stretching the nearest bore size over a housing, or pressing in a seal that is too wide for the recess, is how a rebuild ends up leaking again. You will get a straight answer — either this entry fits, or this size is not in the range — and the second is just as useful to hear before you place the order.

Customer Reviews
$0.00 $0.00
Please choose options.Back to top
Close
$0.00 $0.00
Message Us

Adding to cart succeed!

items in cart.

Subtotal:

Requires a minimum purchase of . And you still need to meet the requirements.

Proceed to Checkout Return to Shopping