Main Seal Rod Seal MPI/MPS Seal 4029584 402-9584
- Description
Product Overview
This is a hydraulic cylinder rod seal — the main seal that sits in the gland at the rod end of an excavator cylinder. As the rod strokes in and out it holds pressure on the oil side and wipes the chrome clean on the return, so hydraulic oil stays in and grit stays out. When it fails, the first sign is a film of oil on the rod and a drip under the machine.
The MPI/MPS profile is a family of its own. IUH, SPGO and SPGW rod seals also sit in excavator cylinder glands, but each family seats into a differently shaped groove, so the profile has to match what is actually machined into your cylinder. If an MPI/MPS ring came out, an MPI/MPS ring is what goes back in.
Identification runs on numbers rather than machine badges. The MPI rod seal 4029584 is catalogued by different suppliers under a string of alternative references, and the marking on the old part is the surest way to match it. Seals reach us through long-standing excavator rod seal manufacturer relationships, and that network is why a single profile can be traced across so many different listings.
Repair shops and fleet maintenance teams buy this ring for a weeping cylinder or a scheduled reseal, while parts distributors restock a hydraulic main seal wholesale line that has run down. What they have in common is a machine that needs to be back at work, so the ring has to be right the first time rather than almost right.
In the hand it is a compact moulded loop with an open centre: an outer body that anchors the seal in its groove and a distinctly darker inner lip that runs against the rod. Rings are bagged with the part number and description on the label, so a drawer of similar-looking seals stays identifiable at the counter.

Key Features
- MPI/MPS groove fit — shaped for MPI/MPS glands, so the ring seats square in the groove instead of being compressed into a profile it was not made for.
- Two working zones — the outer body anchors the seal while the inner lip rides on the rod; each zone does a different job, and both have to be sound for the seal to hold.
- Pressure on one stroke, wiping on the other — cylinder pressure is held at the gland, and the return stroke scrapes the rod clean before anything reaches the oil.
- A loose seal, not a kit — supplied as a single ring, which suits a repair where one seal has failed and the rest of the cylinder stack is still serviceable; distributors take the same ring in quantity for a hydraulic main seal wholesale line.
- Mapped to alternative numbers — the MPI rod seal 4029584 is cross-referenced to a long list of alternatives, so a customer quoting an old number can still be matched to the right ring.
- Common across mixed fleets — MPS rod seal excavator fitments turn up across a wide spread of builds and on other construction machinery hydraulics, so one stock line covers more than a single machine.
Seal Family Comparison
| Profile | Where it fits and what it does |
| MPI/MPS (this seal) | Rod seal for the cylinder gland — holds rod-side pressure and wipes the rod on the return stroke |
| IUH | Main/rod seal profile for cylinder glands; does not interchange with MPI/MPS |
| SPGO | Rod seal profile with its own groove shape and its own numbers |
| SPGW | Rod seal profile, matched by part number rather than by machine brand |
| Double lip rod seal | Rod seal with two sealing edges; close in appearance to a single-edge ring, but the two do not interchange |
| SPG PTFE piston seal | Piston-side seal that runs against the bore, not the gland |
| PTFE profiles | Specified where a parts list calls for a ptfe rod seal instead of a moulded-lip ring |
| HBY buffer seal | Sits behind the rod seal and takes the pressure spikes before they reach it |
| Nylon back-up ring (BRT3) | Supports the seal at the back of the groove under high pressure |
| CFW high-pressure oil seal | Shaft-style seal for high-pressure assemblies, not a cylinder rod seal |
| 430 floating seal | Metal face seal for rotating assemblies such as travel drives |
Part Numbers & Cross-Reference
| Reference group | Numbers (plain / dashed) |
| 123 series | 1237309 / 123-7309 |
| 097 series | 0976014 / 097-6014, 0974307 / 097-4307, 0975407 / 097-5407 |
| 97 series | 974307 / 97-4307, 975407 / 97-5407, 976014 / 97-6014 |
| 105 series | 1052577 / 105-2577 |
| 083 series | 0836106 / 083-6106 |
| 010 series | 0105301 / 010-5301 |
| 208 series | 208215 / 20-8215, 208305 / 20-8305 |
| 83 series | 836106 / 83-6106 |
Fitment Confirmation
- Start with the marking on the old seal. The MPI rod seal 4029584 reference and its alternatives are all we need to begin, and a close photo of the marking covers you if the print is worn.
- Measure if the marking is gone. Rod diameter, bore, groove width and seal height taken off the old part are enough for us, as an MPI rod seal supplier, to check the profile, even when the number has disappeared.
- Photograph the old seal next to a rule, and show the cross-section if it is broken. Lip shape, back profile and any hard parts around it tell us more than a written description can.
- Note the machine model and which cylinder it is — boom, arm, bucket, steering or outrigger. A hydraulic cylinder rod seal in one position can differ from the seal in another, and the model tells us which parts list to check.
- Confirm the lip geometry from the old part. A single edge and a double lip rod seal look similar off the machine but do not interchange, so check the cross-section before ordering.
- Say if the parts list specifies a material. If the manual names a particular compound or calls for a ptfe rod seal, mention it at this stage so the ring is checked against the gland rather than assumed.
Applications
The commonest job is a boom, arm or bucket cylinder that has started to weep at the rod end. Once the rod is drawn and the gland opened, the old ring comes out, the groove is cleaned, and the new seal goes back into the rod seal position. Hydraulic repair shops run the same job across the bench in small numbers — strip, clean, inspect, fit, pressure test. They judge an excavator rod seal manufacturer on one thing: whether the right ring is on the shelf while the machine is still waiting. Fleet maintenance crews work against downtime. The cylinder is leaking on a site, the machine is wanted that week, and there is no second attempt, so the profile has to be confirmed before the seal is ordered rather than after it arrives. MPS rod seal excavator fitments are the most frequent request, but the same ring turns up on other construction machinery and on truck hydraulics, so mixed-machine orders are routine rather than unusual.
Installation & Commissioning
- Clean the groove properly — solvent, a lint-free cloth and a look for burrs or hardened oil.
- A seal seated over debris will leak again however good the ring is.
- Oil the lip, not the groove — a thin film of clean hydraulic oil on the sealing edge lets the ring slide onto the rod without rolling the lip.
- Cover the rod thread — tape or a thin sleeve over the threaded end stops it cutting the lip on the way down.
- Thread damage is a common cause of a new seal leaking.
- Seat it square, by hand — press the ring in evenly with your thumbs or a blunt, soft drift.
- Never stretch it over the rod and never drive it with a sharp tool.
- Pressure test before the machine leaves the bench — cycle the cylinder slowly through full stroke and watch the rod.
- A weep found here costs minutes; the same weep found on site costs a call-out.
- Stop if it will not seat — a ring that needs force is the wrong ring or the wrong groove.
Ordering & Delivery
- Every order is checked against the references we hold before it is picked, so a wrong number is caught at our end rather than at your bench. As an MPI rod seal supplier we would rather query a line than ship a seal that cannot fit.
- Confirm availability and dispatch timing with your sales contact before you commit to a repair date. It is better to know what is on hand than to plan around a date nobody has confirmed.
- Say whether the order is a single replacement or part of a hydraulic main seal wholesale line, and whether mixed references should be bagged together or separated by number.
- Confirm how the carton should be packed, particularly if it will be split across several shelves or passed on to another customer.
- Confirm the commercial terms and paperwork for your order — payment method, Incoterms and the import documents you need — with your sales contact before dispatch, since these are set per order rather than by the part.
Scale & Supply Capability
Guangzhou Wason Construction Machinery has been supplying construction machinery parts since 2015, working with buyers across Africa, the Middle East, South America and other markets. As a trading company we buy through a broad supplier network, so we can cover a wide range of parts, keep fast-moving items in stock for quick dispatch, and combine different references into one consolidated order. Send us a part number, a photo or a cross-reference and we will confirm availability, check the specification with you, and coordinate customised or repeat requirements before shipment.
USD






