Stay In The Know
Join our email list to receive updates and exclusive
offers directly in your inbox.
No Thanks
  • K5V200 Hydraulic Pump Gasket
  • K5V200 Hydraulic Pump Gasket
  • K5V200 Hydraulic Pump Gasket
  • K5V200 Hydraulic Pump Gasket

K5V200 Hydraulic Pump Gasket

Replacement hydraulic pump gasket for ZX450/460, E330C/E330D/336D, R455-7, SK460-8 and EC460. One piece per pack; confirm fitment by pump code.
$0.00 $15.65
    Please select the information you wantX
  • pump gasket
    CHINA
    IMPORT
Wholesale:
10.00% Off
20-49
20.00% Off
50-max
Quantity
-
+
1 * $15.65 = $15.65
  • Description

Diagnosing a Joint Leak

  1. Clean the pump cover and the frame below it, then run the machine up to working temperature. A dry, clean joint shows exactly where the oil is leaving instead of spreading it across old dirt and making every seam look guilty.
  2. Watch the leak path. Oil appearing at the cover seam supports the excavator hydraulic pump gasket; oil at the shaft end, around the regulator or at a hose union points somewhere else and no gasket will fix it.
  3. Check the cover bolts before condemning the gasket. A cover that has worked loose weeps in the same place and looks identical from underneath the machine.
  4. Look hard at the old gasket once the cover is off. Hard, flattened, cracked or torn at a bolt hole means it simply reached the end of its life; a gasket that was clearly trimmed by hand means the wrong reference went in last time and the fault will repeat.
  5. Run a straight edge across the cover face. Score lines, a raised burr or a warped cover will not seal against a new gasket, however good the gasket is.
  6. Note the pump code before you order anything. The plate on the pump is the fastest route to the right zx450 hydraulic pump gasket and it saves a second wait on the machine.

Product Overview

A flat gasket for a big pump's cover joint. The K5V200 hydraulic pump gasket sits between the main pump body and its cover on large excavators. Under pressure it is the part that keeps oil travelling through the pump instead of creeping out along that joint and running down the frame. Bought at repair time, not at rebuild time. Most of these gaskets go out because a cover joint has started to weep, or because the pump is already off the machine for an overhaul and the old gasket will not go back on. Small and inexpensive next to the labour around it, and the one part that decides whether the pump has to come apart twice. The bag keeps the moulded face clean and flat until the cover comes off, and a spare can sit on the shelf without being creased by other stock. Matched to the pump code, not the paint colour. Large machines from different makers can be running the same pump, so the e330c pump gasket and the other machine fitments below are grouped by machine model rather than by brand loyalty. Read the plate on the pump itself when you can, because a unit that has been swapped in the past may not match the machine decal.

Black rubber gasket seal ring in clear packagingBlack gasket ring in clear packaging with WASON label

Build & Sealing Detail

Formed, not cut to fit. The outline, bolt holes and locating tabs are moulded into the excavator hydraulic pump gasket, so it drops onto the cover without trimming, stretching or opening a hole up with a knife. Anything that has to be cut on the bench is a fitment problem, never a fitting technique. It seals by compression, not by adhesion. A flat gasket works because the cover bolts squeeze it just enough to fill the machining marks and light scratches on the joint faces. Consistent from one order to the next. These pieces come from the same hydraulic pump gasket maker who runs the same profile for us, so the second and third pump in a fleet go together exactly like the first rather than needing a different technique each time. Checked before it is bagged. Each gasket is looked over for tears at the bolt holes, handling creases and a clean moulded face before it goes into the bag. Small faults there are precisely what turn into a comeback weep three weeks later.

Machine Fitment

  • Hitachi ZX450 / ZX460 / ZX470 — the zx450 hydraulic pump gasket covers all three codes, so a mixed Hitachi fleet can be held on a single shelf part instead of three.
  • Caterpillar E330C — the e330c pump gasket most workshops reach for when the cover joint on a 330C starts to weep; the pump plate confirms it in a minute.
  • Caterpillar E330D / 336D — the later machines in the same class use the same gasket, so stock bought against a 330D is also usable on a 336D.
  • Hyundai R455-7 — a frequent fitment in mixed fleets on quarry and large earthworks jobs, where the pump runs hot most of the day.
  • Sany SY — listed for SY machines running this pump; send the exact SY model from the plate when you order so the code can be checked against it.
  • Kobelco SK460-8 — the 460-8 uses this reference; if your plate reads differently, send a photo of it rather than ordering on the series name alone.
  • Volvo EC460 — covered on this reference; the pump code on the machine is the deciding detail, not the excavator badge.
  • Suffixes and serial ranges still matter — if the plate carries a suffix such as LC or H, or a serial range you are unsure of, send a photo of the plate together with the old gasket and the match can be checked before dispatch.

Specifications

FieldDetail
Pump codeK5V200
Part typeHydraulic pump gasket - main pump / pump cover gasket
Machine classLarge excavators
Fitted positionBetween the pump body and its cover
ProfileFlat moulded gasket with mounting holes and locating tabs
SurfaceSmooth moulded finish on both faces
Supplied asOne piece per pack in a sealed clear bag
Label detailPart description, quantity 1 pc, Guangzhou Wason Construction Machinery Co., Ltd.

Fitting Sequence

  1. Scrape the old gasket off both faces with a plastic or brass scraper and wipe them clean with a lint-free cloth. Do not run a grinder or a coarse disc over a pump cover face.
  2. Offer the new gasket up to the cover and to the old one before fitting. The outline and every bolt hole should line up without force; if they do not, stop and check the reference for the zx450 hydraulic pump gasket.
  3. Seat the gasket dry on the cover unless the machine's service manual calls for a sealant, and locate it on the dowels or two starter bolts so it cannot shift as the cover goes on.
  4. Fit the cover, run the bolts in by hand, then torque in a cross pattern to the figure in your manual rather than to the point where the cover starts to bow.
  5. Fill and bleed the hydraulic system, run the machine at idle and watch the joint. Check the cover bolts again after the first heat cycle, when everything has expanded and settled.
  6. If oil still appears at the seam, stop. Over-tightening will not close a scored or warped cover face; strip it and check the face before another gasket goes in.

Ordering & Confirmation

  • What to send. The code on the pump plate plus the machine model and serial is the quickest way to have the fitment checked before the order is picked; a square-on photo of the old gasket with a rule alongside it works just as well when the plate is unreadable.
  • One piece or a shelf batch. A single gasket for a machine that is down, or a small batch so the next pump does not hold up the bay - both are handled the same way, and this reference can share an order with other parts.
  • References we do not list. We buy through trusted hydraulic pump gasket partners, so if the pump in front of you needs a gasket that is not shown here, send the code and availability can be looked into.
  • Fleet stock. As a k5v200 gasket specialist, we’re used to fleet orders; send the list of machines you run and each one can be checked against the same reference before the batch is packed.
  • Trade quantities. Repair shops, parts traders and fleet workshops regularly buy this excavator pump gasket in larger quantities alongside other gaskets and seals, and the whole list can travel as one shipment.
  • Timing before you promise the machine. Tell us the date the machine is due back on site and current stock and dispatch timing will be confirmed before you commit to the customer.
  • Documents for export. Shipments to Africa, the Middle East or South America need different paperwork from one another; tell us what your broker asks for when the order is placed.
  • Packing alongside heavy parts. If the gasket travels with pins, rollers or cylinder assemblies, say so and it will be packed flat so the moulded face stays true.

Scale & Supply Capability

Guangzhou Wason has been providing construction machinery parts since 2015, drawing on a broad network of trusted partners and holding stock for fast dispatch so common items move without long waits. Our catalogue covers the replacement parts we list, and we help customers combine mixed orders, check samples before dispatch and coordinate customized requirements when a standard item will not do. Workshops and traders buying excavator pump gaskets in larger quantities get the same checks on every carton. Customers across Africa, the Middle East and South America rely on us for steady supply, careful inspection and export paperwork handled end to end.

FAQ

How do I confirm this gasket matches my pump?

Read the code on the pump plate and compare it with the pump code for this reference, then lay the old gasket on top of the new one: outline, bolt holes and locating tabs should line up exactly. If the plate is worn or unreadable, send a square-on photo of the old gasket with a rule beside it plus the machine model and serial, and the match can be checked before you order.

Where does this gasket sit on the pump?

The K5V200 hydraulic pump gasket fits between the pump body and its cover and seals that joint. It is not a shaft seal and not an O-ring, so if the oil is escaping at the shaft end, around the regulator or at a hose union, this is not the part you need.

My machine is an E330C - is the same gasket used on a 336D?

Yes. The e330c pump gasket and the E330D/336D fitment are covered by this one reference, so a single spare serves both machines. Read the pump plate rather than the machine decal if the excavator has had a pump replaced at some point in its life.

Do I need a full seal kit as well as the gasket?

Only if the pump also needs shaft seals, O-rings or regulator seals. This product is the excavator hydraulic pump gasket for the cover joint on its own; a pump seal kit covers the rest of the seals in the pump, and the two can travel together on one order if you are doing a full reseal.

Should the gasket go on dry or with sealant?

Fit it dry unless the service manual for the machine specifies a sealant or a particular compound. A flat gasket seals by compression under the cover bolts, and an unspecified sealant can hold the cover off its face or leave a bead sitting inside the oil path.

Can I reuse the old gasket if it still looks intact?

No. Once a flat gasket has been compressed under the cover bolts it takes a set and will not spring back to seal again, even if it looks clean and unbroken. Reusing one is how a pump ends up stripped twice for the same leak.

Can I keep a spare gasket on the shelf?

Yes, and it is worth doing if you run several of these machines. Keep it flat in its bag, out of direct sunlight and away from oil, solvent and hot surfaces; a gasket that has been folded or hung on a nail can take a set that shows up as a weep after fitting.

Customer Reviews
$0.00 $0.00
Please choose options.Back to top
Close
$0.00 $0.00
Message Us

Adding to cart succeed!

items in cart.

Subtotal:

Requires a minimum purchase of . And you still need to meet the requirements.

Proceed to Checkout Return to Shopping