Stay In The Know
Join our email list to receive updates and exclusive
offers directly in your inbox.
No Thanks
  • K3V112DTP Hydraulic Pump Gasket
  • K3V112DTP Hydraulic Pump Gasket

K3V112DTP Hydraulic Pump Gasket

Hydraulic pump gasket for K3V112DTP main pumps. Seals the cover-to-housing joint; fits SH200-3, SK200-7/8, SK250-8 and SK330-6/6E/8.
$0.00 $6.35
Wholesale:
10.00% Off
20-49
20.00% Off
50-max
Quantity
-
+
1 * $6.35 = $6.35
  • Description

Product Overview

The K3V112DTP pump gasket is the flat rubber seal that closes the joint between the main pump cover and the pump housing. It is cut to the cover outline, so the whole sealing face goes on in one piece. When a cover comes off for a rebuild or a leak repair, this is the part that goes back on before anything is refilled.

Its job is to hold hydraulic oil inside the cover joint while the pump runs at working pressure. A failed hydraulic pump cover gasket usually shows up as a weep down the side of the housing, oil on the belly plates and a slow drop in tank level rather than as a sudden breakdown.

Most of these go into repair work. Workshops fit one during a pump overhaul, parts counters keep a spare for the machine types they see every week, and fleet teams order when a machine is already in the yard for service. Buyers stocking several pump codes tend to pick them up as part of a larger excavator hydraulic pump gasket order, where one shipment covers a spread of machines.

Old gaskets rarely fail all at once. They harden, take a set in the shape of the cover and stop springing back, so the joint starts weeping after the next heat cycle. That is why a new gasket goes on every time the cover is lifted, even when the old one still looks whole.

A weeping joint costs more than the oil on the floor. Tank level creeps down, the pump runs hotter, and the film of oil catches dust on the housing where it hides the next problem until it has become a bigger one.

Machine Fitment

  • SH200-3 — this cover gasket is listed for the machine, so the pump plate and the gasket pattern should match straight out of the sleeve.
  • SK200-7 and SK200-8 — both suffixes are covered, which means the same gasket serves machines from either batch of that model line.
  • SK250-8 — the next size up in the same series takes the same cover gasket, so one line on the shelf covers two machine sizes.
  • SK330-6, SK330-6E and SK330-8 — all three variants use the same cover pattern, so the larger machines in the group do not need a second part number.
  • Mixed yards — because the list runs across several model lines, one excavator hydraulic pump gasket covers a spread of machines and cuts the number of references you have to carry.
  • Repainted or worn decals — the model name on the boom is not reliable on older machines.
  • Read the pump plate instead, since a replacement pump may not match the original machine.
  • Machines not on the list — send the pump code, the machine model and a photo of the old gasket.

Pump Code Reference

Every hydraulic pump gasket specialist works from the pump code rather than the machine brand, because the same pump turns up under more than one colour of paint. The code on the pump plate decides the part; the decal on the boom does not.

The K3V112 pump is built in several versions — DT, BDT and DTP among them — and the cover pattern differs between them. A gasket cut for one version will not sit flat on another, even though the pumps look similar from the outside.

The code is usually stamped or etched on the pump body, or carried on a small plate near the regulator, sometimes tucked behind the cover bolts. Where a machine has had a replacement pump, the code on the pump beats any record of the original specification.

If you are searching for a K3V112DTP pump gasket or the full K3V112DTP gasket kit, quote the full code and the machine model together. The model supports the machine class, the code supports the cover, and with both we can check the piece before it is packed.

Ordering on “K3V112” alone is where most mismatches start. The three-letter suffix is what changes the cover outline, and as a K3V112DTP gasket specialist the first thing we ask for is a clear photo of that plate.

Specifications

Product typeMain hydraulic pump cover gasket
Pump codeK3V112DTP
Pump seriesK3V112
MaterialRubber
ProfileFlat, contoured, closed outline
MountingMulti-hole pattern matched to the cover bolts
Joint typeBolted main pump cover to housing
Working sideHydraulic oil side of the cover joint
Sealing actionCompressed between cover and housing as the cover bolts are tightened
Supplied asOne gasket per pack; the K3V112DTP gasket kit is listed separately
Pack formatPrinted sleeve with a clear window
Part conditionNew replacement gasket
Dark metal wire ring with mounting tabs

Installation Sequence

  1. Release the pressure and drain down. Park on level ground, shut the machine down and let the hydraulic oil cool before opening anything. Follow the machine's own procedure for releasing residual pressure in the tank and lines.
  2. Clean both faces properly. Old gasket residue, sealant left by a previous repair and any oil film have to come off the cover and the pump body. Wipe with a clean lint-free cloth and let the faces dry before the new gasket goes near them.
  3. Compare the new gasket with the old one. Lay it over the old piece and check that the outline, the holes and the width of the sealing land line up. If the job includes a pump gasket seal kit, compare the other seals the same way; a missing or extra hole shows up straight away and saves a second strip-down.
  4. Seat the gasket dry. Drop it into place on the cover or the housing, whichever the manual calls for, and line up every bolt hole. Do not stretch it over the studs, and do not add sealant unless the service manual specifies one.
  5. Run the bolts down evenly. Bring the cover down square and tighten in a cross pattern in stages, to the torque figure for your machine. Stopping at the first snug point and then torquing the rest in one pass is how covers end up distorted.
  6. Fill, run and re-check. Refill with the specified oil, run the machine up to temperature and watch the joint. A dry joint after the first heat cycle is the result you want; a weep at this stage means the cover comes off again.

Leak Prevention & Storage

  • A cover that is no longer flat — a cover over-torqued in an earlier repair stays slightly dished, so the gasket only contacts the outer edge. Run a straight edge across the face; even a hydraulic pump gasket made to a tight tolerance cannot seal a cover that rocks on a bench.
  • Bolts run down too far — a rubber gasket needs compression, not crushing. Take the bolts down in stages, in a cross pattern, and stop at the figure in the manual.
  • Heat — a joint that runs hotter than it used to will harden the gasket faster. If the pump temperature has climbed, deal with the cause before blaming the seal.
  • Storage before fitting — keep spares flat in their sleeve, out of direct sun and away from oil, and never folded into a toolbox drawer or hung on a hook. A hydraulic pump cover gasket that has taken a crease will not sit true, and a crease in the sealing face is enough to start a weep.
  • A mismatched cover or pump — a used cover from another machine, or a replacement pump with a different cover pattern, is the one cause no gasket can fix. Check the bolt pattern against the gasket before the cover goes back on.

Related Seals & Parts

Cover gasketSeals the joint between the main pump cover and the pump housing
O-rings under the coverSeal the small galleries running through the cover face
Shaft sealSeals the drive shaft where it leaves the pump body
Regulator and control O-ringsSeal the control side of the pump
Pump gasket seal kitUsed when the pump is stripped for a full reseal rather than a cover-off repair
K3V112DTP gasket kitPuts the cover gasket and the seals that sit around it on one reference
Hydraulic oil and filterUsually changed in the same pass as a cover-off repair
Cover bolts and washersEven clamping force across the cover face depends on them

Ordering & Delivery

  1. Start with the pump code. Send the code from the pump plate and the machine model, plus a photo of the old gasket if you have one. That is enough to check the piece against the code before it is packed.
  2. Set the quantity by how you buy. One gasket covers one repair; workshops that keep the common codes on the shelf order in larger quantities for the excavator pump gasket, and bigger orders move into better price tiers.
  3. Confirm stock and dispatch. Ask your sales contact whether the code is on hand and when it can leave. As a K3V112DTP gasket seller we confirm the position per code rather than quoting one blanket lead time for everything.
  4. Add anything else the job needs. If the pump is losing oil at the shaft as well, put the pump gasket seal kit on the same order so the whole repair is covered in one go.
  5. Agree payment, packing and shipping. Payment method, currency, packing and the shipping method to your destination are confirmed with your sales contact before release, together with any documents your customs broker needs.
  6. Check the pack on arrival. Compare the code on the sleeve with the code on the pump before fitting, and raise anything that does not match with your sales contact straight away.

Scale & Supply Capability

Guangzhou Wason has been providing construction machinery parts since 2015, drawing on a broad network of trusted partners and holding stock for fast dispatch so common items move without long waits. Our catalogue covers the replacement parts we list, and we help customers combine mixed orders, check samples before dispatch and coordinate customized requirements when a standard item will not do. Customers across Africa, the Middle East and South America rely on us for steady supply, careful inspection and export paperwork handled end to end.

FAQ

Which excavator models does this cover gasket fit?

This excavator hydraulic pump gasket is listed for SH200-3, SK200-7 and SK200-8, SK250-8, and SK330-6, SK330-6E and SK330-8. If the machine has had a replacement pump, check the code on the pump body rather than the model badge on the boom.

Will a K3V112DT gasket fit instead?

No. The K3V112 family is built in several versions and the cover pattern changes with the version, so a DT or BDT gasket will not necessarily sit flat on a DTP cover. Match the full code stamped or etched on the pump.

Does the gasket need soaking or grease before it goes on?

Neither. It goes on dry, straight out of the sleeve, unless your service manual names a specific sealant for that joint. The bolt holes locate it, and a dry rubber face seals better than one smeared with grease or gasket compound.

Can you match a gasket that is not in your list?

Send the pump code, the machine model and a photo of the old gasket. Matching runs on the pump code, which is the reference a hydraulic pump gasket maker cuts to, so a clear photo of the plate is worth more than a model name.

Is the bolt torque the same on every machine that uses this pump?

No. The same pump code appears on several machine lines with their own cover bolts and their own figures, so use the torque and sequence given in the service manual for the machine in front of you rather than a general rule.

Customer Reviews
$0.00 $0.00
Please choose options.Back to top
Close
$0.00 $0.00
Message Us

Adding to cart succeed!

items in cart.

Subtotal:

Requires a minimum purchase of . And you still need to meet the requirements.

Proceed to Checkout Return to Shopping