K3V112BDT Hydraulic Pump Gasket
- Description
Product Overview
An excavator hydraulic pump gasket sits between the pump body and its cover and does one job: it keeps pressurised oil inside the joint. This one is a flat plate with a large central opening and a ring of bolt holes, shaped to the cover face so the oil passages line up and the cover clamps down on a full sealing surface instead of on metal-to-metal contact.
It is listed for SK200-3, SK200-5, SH200A3 and the plain HD820. One plate covers all four because they share the same pump cover pattern — a detail that matters on site, where the hydraulic pump gasket SK200 and SH200A3 machines need can be the identical part even when the decals differ.
Most of these leave in mixed cartons rather than one at a time. Repair shops add a couple to every seal-kit order, and parts counters keep the K3V112BDT hydraulic pump gasket in spare stock so a leaking pump cover does not idle a machine for a week.
Treat it as a single-use part. Once the cover has been torqued down the plate takes a set, and a gasket that has already been compressed will not seal reliably a second time — fitting a new one every time the pump is opened is normal practice, even when the old plate looks intact.


Material & Build
The plate is cut to the cover pattern by the hydraulic pump gasket specialist we get this reference from, rather than trimmed to fit on the bench. Bolt holes and the central opening have to land in the right place the first time, because a gasket that has to be coaxed over the studs will not sit flat once the cover comes down.
Hole edges are cut clean and the outer contour follows the cover face. A ragged punch leaves a raised burr, and a burr is a leak path: the cover cannot seat evenly, oil finds the high spot, and the joint weeps again within a few shifts.
The sheet is matte black with a smooth surface, thin enough to compress into the machined cover face and stiff enough to stay where it is put while the cover is lowered. The K3V112BDT hydraulic pump gasket is a single-layer flat gasket, so it seals by compression across the whole face rather than by an internal lip or a steel core.
Cover condition matters as much as the gasket. If the cover was pried off with a screwdriver and the face is scored or dished, a fresh plate will not fix it — check the face with a straight edge and dress any burr flat before fitting. When it comes to an excavator hydraulic pump gasket, we would rather see a photo of that face than send a second gasket that fails the same way.
Machine Coverage
- SK200-3 and SK200-5 — the earlier pair on the list. If the plate bolted to the pump carries the BDT suffix, this is the hydraulic pump gasket SK200 owners fit when the cover comes off.
- SH200A3 — same reference. The A3 suffix on the machine does not change the pump gasket, so an SH200A3 and an SK200-3 can be covered from the same shelf position.
- HD820 with no suffix — listed here. If the machine badge adds a number after HD820, check the pump before ordering the hydraulic pump gasket HD820-1/2/3 machines use, because that is a different plate.
- The suffix decides it — a number after the base model usually means a later pump revision with a different cover pattern, so a machine that looks identical on site can take a different gasket. Read the plate bolted to the pump, not the decal on the boom.
- Match on the pump code — the same excavator model can be built with more than one pump over its production life, and the code stamped on the pump is what a hydraulic pump gasket listing uses to identify the part.
- If the plate is unreadable — send a photo of the pump cover, the old gasket laid flat and the machine serial. That is usually enough for us to confirm the reference before you commit to the order.
- Machine | Gasket to order --- | --- SK200-3 | This gasket SK200-5 | This gasket SH200A3 | This gasket HD820 (no suffix) | This gasket SK200-6 | K3V112DT gasket SK230-6 | K3V112DT gasket SK230-6E | K3V112DT gasket HD820-1 | K3V112DT gasket HD820-2 | K3V112DT gasket HD820-3 | K3V112DT gasket SK200-7 | K3V112DTP gasket SK200-8 | K3V112DTP gasket SK250-8 | K3V112DTP gasket SH200-3 | K3V112DTP gasket
Installation Sequence
- Drain and clean. Open the pump as your service manual describes, then wipe the cover face and the pump body face dry — oil left on either face holds the gasket off the surface.
- Remove every trace of the old gasket with a scraper and a little solvent, then a final dry wipe. Leftover fibre creates a high spot and the new plate will not seat around it.
- Check the cover face. Lay a straight edge across it and look for prying marks, scores or a dished centre; a warped cover will leak with any excavator hydraulic pump gasket you fit.
- Set the K3V112 pump gasket in place dry, aligning the bolt holes by hand. Two bolts nipped up lightly will hold it while you check that the opening lines up with the oil passage; most flat cover gaskets of this type go on without sealant, so follow the pump manual if your workshop normally uses a compound.
- Torque in a cross pattern, working across the bolt circle in two or three passes to the figure in your pump manual. Pulling one bolt to full torque first tilts the cover and pinches the plate on one side.
- Refill, run to working temperature and look at the joint again after the first shift. A dry joint on a hot machine is the real pass mark — a joint that is dry at idle can still weep once the oil thins.
Repair Scenarios
- A pump cover weeping after a rebuild — the usual reason this gasket is ordered. The pump goes back together with new seals but the old cover gasket is reused, and oil shows at the joint within days.
- A new plate settles it.
- A 20-ton machine down mid-job — owners on a deadline want the gasket in hand before the pump comes out, so the repair is a morning rather than a week of waiting on a part.
- Mixed-fleet workshops — a shop that services several brands ends up with a row of K3V112 pump gasket references in the drawer. Labelling them by pump code instead of by machine model stops the wrong one going on.
- Parts counters and resellers — shops that keep excavator pump gaskets on hand want the reference that covers the most machines per line, and the BDT plate covers three machine families from one shelf position.
- Scheduled pump servicing — fleets that pull pumps on an hour interval rather than on failure fit a new cover gasket as part of the job, so the machine does not come back for a leak three months later.
- A pump back from a third-party rebuild — covers sometimes return dry-fitted or with a home-made paper gasket. Replacing that with the correct hydraulic pump gasket HD820 plate is quicker than chasing why the joint keeps bleeding.
Specifications
| Product | K3V112BDT hydraulic pump gasket |
| Part type | Main pump cover gasket |
| Sealing position | Pump body to cover joint |
| Form | Flat plate with a large central opening and a ring of bolt holes |
| Colour and finish | Matte black with a smooth surface |
| Pump family | K3V112 series, BDT variant |
| Machine fitment | SK200-3, SK200-5, SH200A3, HD820 |
| Pack quantity | 1 piece |
Ordering & Delivery
- Confirm the machine and the pump. Send the model and serial from the plate plus a photo of the pump or the old gasket; that is the quickest way to be certain the reference is right.
- Set the quantity. One piece covers a single repair; if you are stocking a counter or a fleet, let us know and we will quote a larger lot of excavator pump gaskets.
- Check the current terms. Price, payment method, lead time and dispatch are confirmed when you order, so ask your sales contact for today's figures rather than working from an older order.
- Agree the packing. Gaskets travel flat to protect the plate, and we can pack them with a mixed seal-kit order so everything arrives together.
- Confirm the shipping route. Destination port, consignee details and the documents your customs broker needs are settled before dispatch.
- Check availability before scheduling the repair. We keep the fast-moving references in stock, but it is worth confirming this one is ready to go before the machine goes into the bay.
Scale & Supply Capability
Guangzhou Wason has been providing construction machinery parts since 2015, with a focus on hydraulic pump gaskets and drawing on a broad network of trusted partners, with stock held for fast dispatch so common items move without long waits. Our catalogue covers the replacement parts we list, and we help customers combine mixed orders, check samples before dispatch and coordinate customized requirements when a standard item will not do. Customers across Africa, the Middle East and South America rely on us for steady supply, careful inspection and export paperwork handled end to end.
USD






