• Excavator Cylinder Used NOK Main Seal Rod Seal  IDI/ISI 1672304
  • Excavator Cylinder Used NOK Main Seal Rod Seal  IDI/ISI 1672304
  • Excavator Cylinder Used NOK Main Seal Rod Seal  IDI/ISI 1672304
  • Excavator Cylinder Used NOK Main Seal Rod Seal  IDI/ISI 1672304
  • Excavator Cylinder Used NOK Main Seal Rod Seal  IDI/ISI 1672304
  • Excavator Cylinder Used NOK Main Seal Rod Seal  IDI/ISI 1672304

Excavator Cylinder Used NOK Main Seal Rod Seal IDI/ISI 1672304

NOK IDI/ISI rod and main seals for excavator cylinders. Match the part number or measurements to your old ring before ordering.
$0.00 $7.65
    Please select the information you wantX
  • NOK ROD SEAL
    167-2304
    5J-8200
    167-2294
    5J-8150
    5J-8225
    5J-0964
    167-2300
    5J-8175
    167-2302
    167-2310
    5J-8238
    167-2312
Quantity
-
+
  • Description

Product Overview

This is the ring that keeps hydraulic oil inside an excavator cylinder while the rod strokes in and out. It sits in the NOK IDI/ISI family, which covers both the piston-side main seal and the gland-side rod seal, and the option list holds every reference we stock in that family. Pick the number that matches the one on your old ring and the repair stays simple. A hydraulic cylinder rod seal usually gives notice before it fails. You see a thin film of oil on the chrome, a drip hanging under the gland at the end of a shift, or a cylinder that creeps down after the machine is parked. Caught there, the job is a seal and a clean-up; left alone, the rod scores and the repair grows. Workshops often quote the part by name instead of by number, so an idi isi rod seal enquiry can arrive with nothing more than a machine model attached. If that is your starting point, read the moulded number off the old ring or measure it and work from the reference list. The size decides the fit, not the name on the quote. As an excavator cylinder seal supplier we keep these references for repair shops, parts counters and fleet workshops that need a cylinder back in service.

Seal Profile & Material

The rings arrive pale yellow and slightly translucent, moulded in one piece with a rounded body and a fine working lip. The lip is the part that flexes under pressure and returns to shape when the load comes off. A sharp, even edge and a clean mould line are what you look for when you unwrap one.

Which end of the cylinder you are repairing changes what you are comparing. An excavator main seal works on the piston against the bore, while the rod seal runs against the chrome rod, and each meets different wear and different contamination. Check the part you removed carefully before choosing a reference.

Numbers for this family reach us from hydraulic cylinder seal manufacturer catalogues and from the references moulded on the rings customers send in. When the two disagree, the measured size decides, and we will say so rather than ship a ring that is close but not right.

The material is a rubber-like elastomer, and the compound grade is not printed on the bag. If the machine runs high-temperature oil, fire-resistant fluid, or works in hard cold, tell us the fluid and the working temperature before ordering so the reference can be checked against it.

Each seal comes bagged with a label showing the reference and the quantity, which keeps a drawer of mixed sizes readable. Leave that label with the ring until it is fitted; it is the quickest way back to the same size next time.

Hand holding pale yellow O-ring seals above a printed labelPile of pale yellow translucent O-rings beside a printed labelPale yellow seal rings piled on a printed part-number label

Cross-Reference Part Numbers

DesignationNOK IDI/ISI rod seal and main seal
Main reference167-2304 / 5J-8200
Main reference, no hyphen1672304 / 5J8200
Cross-reference167-2294 / 5J-8150
Cross-reference5J-8225
Cross-reference5J-0964
Cross-reference167-2300 / 5J-8175
Cross-reference167-2302
Cross-reference, no hyphen1672302
Cross-reference167-2310 / 5J-8238
Cross-reference167-2312
Cross-reference, no hyphen1672312
Cylinder endRod gland or piston

Fitment & Part Matching

  1. For an excavator rod seal wholesale order, start with the cylinder rather than the machine.
  2. Note the excavator model and which cylinder is leaking, whether boom, arm, bucket, blade or stabiliser, because one machine can use different seal sizes at each end.
  3. Read the old seal. Whether the workshop quoted you an idi isi rod seal or just a part number, the reference is normally moulded into the ring face and often printed on the bag as well. Photograph it before you clean it, while the number still reads.
  4. Measure with a caliper: inside diameter, outside diameter and height, plus the direction the lip faces. On a hydraulic cylinder rod seal, height and lip shape decide the fit as much as the diameter does.
  5. Match against the reference list. Go by the number first; if it has worn away, match the three measurements and the lip direction instead.
  6. Send the details if nothing lines up. A photo of the old ring beside a rule, plus the machine model, is usually enough for us to identify the size we hold.
  7. Say so if the whole cylinder is being resealed. We can add the rest of the excavator cylinder seal kit for that cylinder to the same order so the parts travel together.

Repair Applications

  • Boom and arm cylinder reseal: the everyday case of a high-hour machine weeping at the gland from an idi isi rod seal, caught before the chrome is marked.
  • Bucket cylinder repair after impact, where the lip has been nicked or rolled and the seal is changed together with a fresh wiper.
  • Piston-end work: when the excavator main seal on the piston is being changed in the same strip-down, order both references together.
  • Bench rebuilds in a repair shop, where cylinders are stripped, cleaned and resealed on the bench and the same reference keeps coming back.
  • Field service calls, where a machine is down on site and having the right seal on the van saves a second trip.
  • Full reseal in one go, where an excavator cylinder seal kit is already going onto the bench and this ring goes in with the rest of the set.

Installation Sequence

  1. Park on level ground, lower the attachment, release the pressure and cap the lines before anything is opened. A cylinder can hold oil under pressure well after shutdown.
  2. Pull the rod and keep the gland nut, shims and wiper in the order they came off.
  3. Clean tray, clean hands: grit carried into the gland is the most common reason a new seal weeps again.
  4. Inspect the chrome and the bore. Run a fingernail along the rod where the hydraulic cylinder rod seal runs; anything you can feel as a step or a pit will cut a new lip within hours, so the rod has to be sorted first.
  5. Oil the seal and seat it square. Never stretch it over threads or a sharp shoulder, and tape the threads if no fitting sleeve is to hand.
  6. A twisted ring leaks from the first shift.
  7. Reassemble and torque the gland to the machine specification, then cycle the cylinder slowly through full stroke several times to bleed the air out.
  8. Check for weep after those first cycles and again once the oil is hot. A dry gland at working temperature is the real pass.
  9. If a hydraulic cylinder seal kit is going in as a set, change the wiper and the backup rings in the same session; leaving old ones behind shortens the life of the new seal.
  10. Write the reference on the machine service sheet so the next gland repair starts from a number instead of a measurement.

Ordering & Delivery

  • Choose the option that matches your old seal. Each reference in the list is a separate size and a separate item, so the price shown applies to that one.
  • Tell us the number of cylinders rather than the number of pieces if that is easier, including excavator rod seal wholesale quantities for a workshop or parts counter, and we will confirm availability before you pay.
  • We are a trading supplier, not a hydraulic cylinder seal manufacturer. Stock comes through seal manufacturer and trade partners we have bought from for years, and every ring is checked against the order before it is packed.
  • Payment, lead time and freight are quoted for each order. Confirm the current price, the payment method and the delivery time for your country with your sales contact before paying.
  • If you want the complete set for the cylinder, ask for the hydraulic cylinder seal kit and we will quote the references together.
  • Seals are bagged and labelled; if they are travelling with a larger parts order, tell us so everything is packed on one list.
  • For customs, tell us the invoice description your broker needs and we will use it on the documents.

Scale & Supply Capability

Guangzhou Wason Construction Machinery has been supplying construction machinery parts since 2015, working with buyers across Africa, the Middle East, South America and other markets. As a trading company we buy through a broad supplier network, so we can cover a wide range of parts, keep fast-moving items in stock for quick dispatch, and combine different references into one consolidated order. Send us a part number, a photo or a cross-reference and we will confirm availability, check the specification with you, and coordinate customised or repeat requirements before shipment.

FAQ

Can I get the other seals for the same cylinder at the same time?

Yes. Send the machine model and the cylinder you are working on, and the parts list from the workshop manual if you have it. We will quote the other references for that cylinder alongside this ring, so an excavator cylinder seal kit for the job can be put together in one order.

Should I replace every seal once the cylinder is open?

It depends on what comes out. If the wiper and the backup rings are still flexible and unmarked, this ring on its own may be enough; if they are hardened, flattened or nicked, a hydraulic cylinder seal kit is the cheaper route than a second strip-down. Photograph the parts as you remove them and we will tell you which ones look finished.

Are these original NOK seals?

The seals are supplied under the NOK IDI/ISI designation shown on the option you select. We source through hydraulic cylinder seal manufacturer and seal trade channels rather than running a production line ourselves, so if your customer needs particular documentation or marking with the shipment, tell us before you order and we will confirm what can be provided.

Can you check my reference before I order?

Yes, that is most of what we do throughout the day. Send the machine model, the cylinder, the number on the old ring and a photo of it next to a rule, and we will compare that with what we hold. As an excavator cylinder seal supplier we would rather spend five minutes on a photo than have you fit the wrong size.

Will the same seal fit different excavator brands?

The same physical seal is often sold under more than one part number depending on which brand badged the machine, which is why the number list matters more than the badge on the panel. Match the number or the measured size, and if two references look close, send both and we will compare them side by side. Buyers ordering excavator rod seal wholesale volumes work from the number list for exactly this reason.

What is the difference between the main seal and the rod seal in this listing?

The rod seal sits in the gland and seals around the chrome rod; the excavator main seal sits on the piston and seals against the bore. Both belong to this NOK IDI/ISI family and both wear, but differently: the rod seal meets dirt from outside, the main seal meets pressure from inside. Tell us which one you are replacing, and take both if the cylinder is coming apart anyway.

Customer Reviews
$0.00 $0.00
Please choose options.Back to top
Close
$0.00 $0.00
Message Us

Adding to cart succeed!

items in cart.

Subtotal:

Requires a minimum purchase of . And you still need to meet the requirements.

Proceed to Checkout Return to Shopping