Stay In The Know
Join our email list to receive updates and exclusive
offers directly in your inbox.
No Thanks
  • Excavator Cylinder Seal BUSHING
  • Excavator Cylinder Seal BUSHING
  • Excavator Cylinder Seal BUSHING
  • Excavator Cylinder Seal BUSHING

Excavator Cylinder Seal BUSHING

Split metal cylinder seal bushings for excavator hydraulic cylinders, from 45/50 mm to 175/170 mm. Match yours by size code, marking or photo.
$0.00 $1.05
    Please select the information you wantX
  • BUSHING
Quantity
-
+
  • Description

Bushing or Seal

An excavator cylinder seal bushing and a rod seal come out of the same cylinder during a reseal, and the two get confused. The seal keeps the oil in; the band holds the rod steady so the seal lip has something true to run against.

That is why a bushing alone will never cure a leak. If oil is passing the rod, the hydraulic cylinder seal bushing may well be worn, but the seal has to be renewed as well, because the band only removes one of the reasons the seal failed.

Material is the other question that comes up. A bronze excavator cylinder bushing and a steel-backed band behave differently against a chrome rod, so the grade named in the parts book is worth following rather than substituting on size alone.

Wear shows up as an oval bore, a polished or scored inner face, a crack through the slit, or a rod that can be rocked by hand once the gland is open. A band that has lost its spring is finished, whatever the measurement says.

Fitting a new seal over a tired band is one of the common reasons a fresh reseal does not last. The two parts cost little next to another strip-down, which is why they are usually changed together.

Product Overview

An excavator cylinder seal bushing is the thin metal band that sits inside a hydraulic cylinder and keeps the moving rod or piston running on centre. Each one is an open-ended ring with a single slit, so it can be closed by hand, slipped into a bore that is already machined, and released to sit flush against the wall.

Its work is guidance rather than sealing. The band carries the side load between the moving part and the bore, which keeps the running clearance even along the whole stroke instead of letting it open up on the loaded side.

Bushings are listed one piece at a time rather than only inside a full seal kit, which suits a workshop that already has a cylinder apart and has found one worn band. As an excavator cylinder bushing supplier we keep the sizes separate so a parts counter can restock the ones that move fastest without buying a whole kit.

Most orders come from hydraulic repair shops, construction machinery parts distributors and fleet workshops. They all need the same three things before ordering: the bore the band sits in, the band length, and the material grade the parts book calls for.

Metal split band rings in a clear plastic bag with loose rings.Open metal split band rings leaning against each other.

Matching a Bushing to the Cylinder

  1. Look for the marking on the old band first. A stamped or etched size is the quickest match, and a wipe with a rag is usually all it takes to read it. If the marking has gone, measure the bore, the outside diameter of the band and its length with a caliper, and note the three figures as the excavator cylinder bushing size.
  2. Record the machine model and which cylinder the part came from, whether boom, arm, bucket, blade or outrigger, because the same machine can use a different band at each position. Photograph the old part beside a rule with the slit visible. As an excavator cylinder bushing supplier we can usually place a part from a clear photo and three measurements together.
  3. Check the material line in the parts book. If nothing in the list lines up, send the measurements anyway.
  4. Every code carries three figures: the two diameters the band fits between, then the band length. The two diameters always sit 5 mm apart, so the wall is the same on every size in the list. That makes the excavator cylinder bushing size quick to verify and easy to misread. Two codes five millimetres apart in the first figure belong to two different cylinders, and the nearest one is not a substitute. Write the numbers down in the order they are printed, diameters first and length last, so nothing gets transposed when the part has to be measured rather than read. The figures mean the same thing whether they come off a cylinder seal bushing manufacturer's label or off your own calipers, so a marked part and a measured part can be compared directly. A caliper across the bore and across the band gives a number worth trusting; a tape measure is fine for a first look and poor for a decision. If the old band is worn oval, cracked or broken, measure the bore and the rod or piston it ran on instead. Those surfaces keep the original dimension better than the worn part does.

Where the Band Is Used

  • Boom, arm and bucket cylinders: the gland end is where a hydraulic cylinder seal bushing usually wears first, because the rod works side to side under load throughout the day.
  • Piston-side guidance: on cylinders without a separate wear ring, the band keeps the piston concentric in the bore and stops metal-to-metal contact.
  • After a repair: when a scored bore has been cleaned up or a rod has been straightened or re-chromed, a fresh band restores the clearance that the damage opened up.
  • Planned reseal: a cylinder seal bushing replacement is normally scheduled together with the seal kit, since the cylinder is already stripped and the old band is already out.
  • Fleet repeat work: once the cylinder seal bushing manufacturer's size code for a machine is written down, reordering for the rest of the fleet becomes a one-line instruction.
  • Counter stock: distributors hold the middle of the size range so a walk-in repair does not wait on a custom excavator cylinder bushing to be made.

Specifications

Product typeSplit metal guide band for excavator hydraulic cylinders
Component familyLoose seal component, a guide band and not a lip seal; bronze excavator cylinder bushing grade as named in the parts book
ProfileOpen-ended ring with a single slit
Outer surfaceBrushed metal
Inner faceDark machined surface
Excavator cylinder bushing size codeThree figures, for example 100*95*40
Sizes listed45/50 mm to 175/170 mm pairs, band lengths 15 mm to 60 mm
PackingEach bushing bagged with a printed label
Unit of saleOne piece
Matching referencesSize code, marking on the old part, photo or machine model

Fitting and Seating

  1. Clean the bore before anything goes in. Old seal material, burrs and hardened grease hold the band off its seat, and a hydraulic cylinder seal bushing that sits proud will wear on one side.
  2. Check the bore and the rod or piston for scoring and out-of-round. A damaged bore simply copies itself onto the new band.
  3. Close the slit by hand, start the band into the bore square and let it spring open into its groove. Do not drive it in with a punch on the slit edge.
  4. Seat it fully, then check the gap at the slit and the excavator cylinder bushing size against the old part. A band standing proud of its groove is not home yet.
  5. Oil the running surface with system oil before the rod goes back, then work the rod through its full stroke by hand where the cylinder allows, to feel for tight spots.
  6. Where the machine manual gives clearances or torque figures, follow the cylinder seal bushing manufacturer's figures rather than a general rule of thumb.
  7. A cylinder seal bushing replacement is also the moment to look at the rod chrome and the gland threads, because a cylinder that is already open costs far less to put right than one that has to be stripped twice.

Ordering and Delivery

Unit of saleOne bushing per piece
PackingIndividually bagged with a printed label
Outer carton quantityConfirmed with your sales contact
Stock positionConfirmed per size by your excavator cylinder bushing supplier before payment
Dispatch timeConfirmed against stock when you order
Combined ordersDifferent sizes and seal references can be consolidated
Custom sizesQuoted as a custom excavator cylinder bushing to your measurements
Label contentPart reference printed on each bag for checking in
Payment termsConfirmed with your sales contact
Shipping methodConfirmed per destination and order size

Scale & Supply Capability

Guangzhou Wason Construction Machinery has been supplying construction machinery parts since 2015, working with buyers across Africa, the Middle East, South America and other markets. As a trading company we buy through a broad supplier network, so we can cover a wide range of parts, keep fast-moving items in stock for quick dispatch, and combine different references into one consolidated order. Send us a part number, a photo or a cross-reference and we will confirm availability, check the specification with you, and coordinate customised or repeat requirements before shipment.

FAQ

How many bushings does one cylinder take?

It varies with the cylinder design and with the position on the machine, so the parts book for that model and that cylinder is the reliable answer. Compare it with what came out of the bore you are working on; if only one band came out, only one goes back.

Is this a bronze excavator cylinder bushing?

The bands in this list are metal, with a brushed outer face and a darker machined inner face. Bronze is a grade question rather than a size question, so if the parts book specifies bronze, say so when you enquire and we will confirm which grade is available for the size you need.

Can you supply a custom excavator cylinder bushing if my size is not listed?

Send the bore, the outside diameter and the band length, or a drawing of the part, and the size will be checked against what can be produced. Machines that sit between the listed 5 mm steps, or older cylinders with unusual dimensions, are the usual reasons for asking.

Does the band need reaming or machining after it is fitted?

The bands are supplied finished and go into the bore as they arrive; the checks afterwards are for seating, slit gap and free rod movement rather than machining in place. If the bore itself is out of round, that is a bore repair job and should be settled before a new band goes in.

Should a cylinder seal bushing replacement always be done together with the seals?

When the cylinder is already open and the seals are being renewed, change both, because the band sets the clearance the new seal runs in. A band on its own is worth replacing when it is worn, cracked or has lost its spring and the seals are still holding.

Customer Reviews
$0.00 $0.00
Please choose options.Back to top
Close
$0.00 $0.00
Message Us

Adding to cart succeed!

items in cart.

Subtotal:

Requires a minimum purchase of . And you still need to meet the requirements.

Proceed to Checkout Return to Shopping