Control Valve Hydraulic Pump Use SMALL SPGO
- Description
Product Overview
This is a carbon ring that sits in the seal stack of an excavator control valve or hydraulic pump, listed here by size rather than by machine model. Every option in the size selector is a single ring, so a valve that needs four different rings is four selections. There is no boxed set and no filler parts — you order exactly the rings the job consumes.
In service the ring runs against a moving bore while the softer element behind it does the sealing. That division of work is why the ring is firm rather than soft: it takes the sliding contact and the side load, holds the seal square in its groove and keeps the rubber from being pushed into the gap under pressure. Once the ring wears thin or picks up a score line, the section starts to creep or weep.
Workshops and parts counters make up most of the demand. A shop selling control valve seal kits should carry the individual rings as well as the boxed kits, because a valve bank often needs two or three sizes and no more — buying a full set just to get one ring leaves the rest sitting on the shelf.
Small diameters dominate the list, and the steps between them are fine — several options sit only a fraction apart rather than a whole size apart. Buyers putting together hydraulic seal kits usually take the common diameters in larger quantity and the odd sizes in ones and twos, which is how the sizes are laid out here.
If you are working from a small spgo seal kit that is already apart on the bench, go ring by ring and note which section each one came from. Sizes repeat across sections often enough that a mixed pile is the most common reason a fresh ring will not seat.
The ring is carbon, not rubber: dark, dense and machined flat on both faces, with the closed circular shape shown in the photographs. It holds its form when you pick it up, which is exactly what you want from the part that takes the sliding contact. Inside the stack it is the sliding partner to the bore. The elastomer behind it supplies the squeeze that seals, while the carbon ring keeps that elastomer square, stops it being driven into the gap under pressure and absorbs the sideways load the spool or piston puts on it. Rings are sold loose because they wear unevenly. A control valve seal kit may cover a whole valve bank, but in practice two or three positions wear first and the rest of the set sits on the shelf, so buying by size keeps your stock matched to what actually fails. Section thickness matters as much as diameter. In an spgo hydraulic seal kit a 20 × 2 ring and a 20.4 × 2 ring are different parts for different grooves — the second figure is a size, not a tolerance. What wears them out: contaminated oil, a scored or ridged bore, and misalignment during assembly. A ring that comes out with a bright band on one side or a flattened edge is telling you the bore or the alignment needs attention before a new one goes in. It is not a substitute for an O-ring. Where the groove also takes an O-ring or a back-up ring, fit those as well — a carbon ring on its own will not seal a joint that was designed around a rubber element.
Machine Applications
- Spool sections in a control valve — a worn ring shows up as a function that creeps, drops under load or refuses to hold position, and the repair starts by opening the section and matching the old ring to the list.
- Pump control and servo bores — response goes slow or uneven before anything leaks visibly, and the ring is usually the first part out of the stack.
- Full valve jobs — when a machine is in for a complete control valve seal kit rebuild, the loose rings go onto the same parts list as the seals and are fitted in the same session.
- Mixed fleets — an excavator control valve seal kit list from one model often shares groove diameters with another machine on the same yard, so one tray of rings can cover more than one machine.
- Pump overhauls — if the pump is already open for a hydraulic pump seal kit, changing the carbon ring while the stack is accessible saves opening it a second time later.
- Repair shops serving several customers — keeping the common diameters of the small spgo seal kit on the shelf lets a valve job finish the same day instead of waiting on a single ring.
- Owner repairs — one ring, one measured size, ordered without buying a set the machine will never use.
Size Range And Specifications
| Ring type | Carbon ring in the SMALL SPGO pattern |
| Working location | Control valve and hydraulic pump |
| Supplied as | Loose seals, one ring per size selection |
| Size notation | Diameter × section thickness, in millimetres |
| Smallest size listed | 6 × 2 mm |
| Largest size listed | 55 × 2.5 mm |
| 1.5 mm and 1.6 mm sections | 17 × 1.5 mm and 9 × 1.6 mm |
| 2 mm section | 6 × 2 mm through 38 × 2 mm |
| 2.5 mm section | 50 × 2.5, 51 × 2.5, 52 × 2.5 and 55 × 2.5 mm |
| Fine-step diameters | 16.2, 18.5, 19.5, 20.4, 20.5, 20.6, 20.8, 21.5, 21.6, 21.8, 22.8 and 23.5 mm |
| Total sizes listed | 48 |
| Ring form | Closed circular ring, single piece |
Measuring The Old Ring
- Clean the ring, then let it relax before you measure. A ring taken straight out of a groove still carries the distortion it picked up in service and will read oval.
- Measure the inside diameter across the ring, then again at 90° to the first reading. Take the smaller figure — the larger one is usually where the ring has been stretched over a land.
- Measure the section thickness with the caliper jaws square to the face, not across a rounded or worn edge, and write it down to one decimal place.
- If the ring broke on removal, measure the groove instead: the land it sat on for an inside ring, or the bore it ran against for an outside ring.
- Compare before you round. Sizes a fraction apart are separate options in this small spgo seal kit range, and rounding a reading to a whole number is the most common way a ring gets ordered wrong.
- Work from the ring rather than the parts book. The catalog for a hydraulic pump seal kit may list the ring under a machine model and a superseded number, but the groove in front of you decides the size.
- Write both figures on the packet and, on an excavator control valve seal kit job, note which section of the valve each ring came out of — the same diameter can appear in two places with different section thicknesses.
Fitting And Handling Notes
- Flush before you fit. Grit left in the groove turns a carbon ring into a lap and scores the bore on the first stroke.
- Oil, not grease. Wet the ring with the hydraulic oil the machine runs on so it slides squarely into the groove.
- Press by hand, working around the circumference with both thumbs, and never file, sand or trim a ring to make it seat — a ring that needs a tool to go in is the wrong size, and a sanded face will not hold.
- Check the bore and the groove first: a ridge, a burr or a score line will finish a new ring in a short time, and it is cheaper to deal with it now than to open the same section twice.
- Replace the elastomer behind the ring. On an spgo hydraulic seal kit rebuild the ring and its O-ring wear together, and a new ring against a hardened O-ring will leak again.
- Keep sizes apart on the bench. A valve bank brings several rings out at once, and two similar diameters swapped between sections will not seal.
- On a hydraulic pump seal kit rebuild, check the ring grooves for burrs before the pump is closed up — a pump is harder to open a second time than a valve section.
- Run the function through its full stroke at low pressure a few times before full load, then check for creep and weeping at the section you worked on.



Ordering And Confirmation
- Write the size exactly as the list gives it — diameter first, section second — together with the quantity you want for each size.
- If you are unsure, send a photo of the old ring beside the caliper reading and we will tell you which option it matches before you commit to the order.
- Mix sizes freely. Each size carries its own quantity, so a valve bank and a hydraulic pump seal kit requirement can be covered on one order without buying sets you will not use.
- Confirm availability for each size. We check what is on the shelf against your list and tell you before the order is accepted if a size is short, rather than substituting silently.
- Confirm how you want the rings packed and marked. Separate bags per size are the usual way for a mixed order and save sorting at the bench.
- Lead time, dispatch and payment terms are confirmed with your sales contact when the order is placed, since they depend on the sizes and the destination.
- Tell us if the rings are part of a larger requirement. Since we offer control valve seal kits, we can put loose rings on the same order as the kits, O-rings and other parts you are already buying.
- If you buy for resale, send your size list once and reorder from it. People who stock hydraulic seal kits for resale usually keep a written list of the diameters and sections that move and reorder against quantities rather than measuring again.
Scale & Supply Capability
Guangzhou Wason has been providing construction machinery parts since 2015, drawing on a broad network of trusted partners and holding stock for fast dispatch so common items move without long waits. Our catalogue covers the replacement parts we list, and we help customers combine mixed orders, check samples before dispatch and coordinate customized requirements when a standard item will not do. Customers across Africa, the Middle East and South America rely on us for steady supply, careful inspection and export paperwork handled end to end.
USD








